Fix Linux Mint 14 Wired Connection Not Working Tutorial

Home > Linux Mint > Linux Mint 14 Wired Connection Not Working

Linux Mint 14 Wired Connection Not Working


Contents1 No wireless connection at all1.1 (obsolete)1.2 Broadcom: install the right driver1.3 Switch the wireless card on1.3.1 Disconnect the ethernet cable (LAN)1.3.2 Reset the rfkill status in the BIOS / UEFI1.3.3 B. Also a machine that only boots with my USB stick in is quite fun More weirdness as usual Posted 2 years ago # AdamW - Member The modprobe wouldn't give you Broadcom: install the right driver 1.2. have a peek here

Been gifted an old laptop. asked 2 years ago viewed 7773 times active 11 days ago Related 2Configure Ethernet DSL w/ static IP1Understanding Linux routes in Proxmox0Wired Network Occasionally Fails (Debian)0Linux Mint 17 cannot connect to Realtek wireless chipset 2.4. Does "lsmod" show that the driver has been loaded? dig this

Linux Mint Wireless Connection Not Working

You must not work with the public much. -- Trilby----How to Ask Questions the Smart Way Offline #3 2013-03-07 15:12:38 broi Member From: Bosnia & Herzegovina Registered: 2011-12-10 Posts: 127 Re: wiskyrocknroll 12,711 views 11:32 What To Do After Installing Linux Mint 17 - Franks Helpdesk - Duration: 33:24. Provide us with "ip r" output as well after an unsuccessful connection try. Tip: Did you forget to force Windows to release the IP address, and you don't want to boot Windows to do it as yet?

Wireless internet problems fall into two subcategories: either you have no connection at all, or you have a flaky weak connection. If you're an experienced and advanced Linux user: the Github account of lwfinger contains even more drivers for wireless chipsets. obsoleted. Linux Mint No Internet Connection Creating a local wired network that gets internet-connection from local wifi?

If so, the terms are not the same. teklek411 372,406 views 8:23 linux mint 17.2 cinnamon 2.6 How to add wifi ethernet or other connections - Duration: 6:23. require dhcp_server_identifier # A hook script is provided to lookup the hostname if not set by the DHCP # server, but it should not be run by default. In any case before re-installing you can try if you can connecting using the current Arch ISO.

WTAF. Linux Mint Can't Connect To Wired Internet You are currently viewing LQ as a guest. IT WORKS [poasting from it now over WiFi] Thanks everyone. When you have an Atheros wireless chipset and it's running on the ath10k, ath9k or ath5k driver, then you might have a very slow and/or unstable connection with certain types of those

Linux Mint No Ethernet Connection

for them). Click Save. Linux Mint Wireless Connection Not Working On some laptops, the wireless chipset is being disabled automatically when the laptop is already connected to the internet by means of an ethernet cable (LAN). Linux Mint Ethernet Not Working Then in the terminal (use copy/paste in order to avoid typing errors): gksudo leafpad /etc/modprobe.d/blacklist.conf Press Enter.

Do you want me? navigate here Does "lsmod" show that the driver has been loaded? a. The connection speed should be all right now. Linux Mint 17 Wired Connection Not Working

I also have been trying to get tech support from my ISP. When DHCP was working were you getting a default gateway? networking linux-mint share|improve this question edited May 30 '14 at 18:05 Braiam 17.1k955103 asked May 30 '14 at 17:26 msinfo 106112 Run tcpdump -i eth0 -n in another shell. Check This Out Mar 07 10:20:42 broislinux systemd[1]: Startup finished in 3s 539ms 744us (kernel) + 1min 30s 712ms 603us (userspace) = 1min 34s 252ms 347us. -- Subject: System start-up is now complete --

Posted 2 years ago # Conqueror - Member lspci | grep -i net will tell you what network interfaces you have... Linux Mint Can't Connect To Internet No avail? Execute dhclient while tcpdump runs and add the tcpdump output to your question. –Hauke Laging May 30 '14 at 17:58 Why aren't you using NetworkManager to mange your network

Thanks in advance....

Go back to Linux, and set that address as a static address ip addr flush dev eth0ip addr add dev eth0Then, see if you can ping It *could* be that it is trying to negotiate 100Mb duplex which can be a swine; forcing it both sides for 100Mb is what we do on our servers. Get the answer skittleFeb 14, 2015, 1:51 AM How new is your motherboard? Linux Mint Ethernet Driver You need internet connection for using those, so first establish a temporary internet connection by ethernet cable or by another wireless dongle.

So far I've discovered that using DHCP, the network manager would show an interminable "connecting" and then disconnect after a few minutes. I tied Ubuntu 12 [selected the wrong image, oops] and it's doing the exact same thing - it tries to connect for about 30 seconds and then drops out with "has Gilles Letourneau 1,561 views 6:23 Linux Mint 18 " Sarah " - Duration: 13:57. Now you can always simply double click this file, before you exit Windows.

Bad wireless connection 2. You can do this as follows: Launch a terminal window. (You can launch a terminal window like this: *Click*) Type (use copy/paste to avoid typo's): lsmod | grep ath Press Enter. Help? Rating is available when the video has been rented.

More resources Tom's Hardware Around the World Tom's Hardware Around the World Denmark Norway Finland Russia France Turkey Germany UK Italy USA Subscribe to Tom's Hardware Search the site Ok About This might cause a bad unstable connection or even a complete failure to establish any connection at all. I think these ports are USB 1 only - it's really really rather slow, even the spinning rust is quicker! In case you have a Realtek wireless chipset that doesn't work at all, or often loses connection and runs below its ordinary speed, that chipset probably needs a better driver.

I used a solution that I happened to already have on my laptop on an exam. Nothing is too wonderful to be true, if it be consistent with the laws of nature -- Michael FaradayYou assume people are rational and influenced by evidence. Posted 2 years ago # gofasterstripes - Member ifconfig -a

eth0 Link encap:Ethernet HWaddr 00:1b:24:6f:f1:9e
inet6 addr: fe80::21b:24ff:fe6f:f19e/64 Scope:Link
RX packets:0 When it's off, or when no mention is made of Power Management at all, you don't need to do anything.

The error for that is host unreachable After a little googling, I looked at the route command.