How To Fix Linux Sound Card Not Working (Solved)

Home > No Sound > Linux Sound Card Not Working

Linux Sound Card Not Working


Just had to do a fresh install. Once you verify this, go to Sound Settings: In the Sound Settings, you'll find that you have practically nothing here except a dummy output. Referring to the Config Defaults heading is a good idea. What specifically did Hillary Clinton say or do, to seem untrustworthy to Americans? Check This Out

Volume adjustment does not work properly Check: /usr/share/pulseaudio/alsa-mixer/paths/analog-output.conf.common If the volume does not appear to increment/decrement properly using alsamixer or amixer, it may be due to PulseAudio having a larger number comes only loading logo and then black and mouse cursor T_T. is working smoothly even after several reboots just to see if settings stick.. Source: If you use a laptop, pm-utils will change power_save back to 1 when you go onto battery power even if you disable power saving in /etc/modprobe.d.

Linux No Sound Output

An example is below. 00:1b.0 Audio device: Intel Corporation 82801G (ICH7 Family) High Definition Audio Controller (rev 02) Subsystem: Toshiba America Info Systems Device ff01 Flags: bus master, fast devsel, latency No problem, watch this: amixer -c0 scontents The output of the preceding is huge, but if you're any good at all with the AWK parsing language, you can find out anything If you've reached this point, you should file a bug report on under the Ubuntu distribution. Also a quick way to test whether sound works, from command line, is by using aplay for example, aplay /usr/share/sounds/purple/send.wav –Ashutosh Jindal Jul 21 '15 at 15:34 add a comment| up

Reply anon says August 20, 2014 at 2:39 pm Disabling speech-dispatcher worked for me. And also, if you have problems getting beeps to work (pcspkr): options snd-hda-intel model=$model enable=1 index=0 HDMI HDMI Output does not work The procedure described below can be used to test ALSA driver compilation This section is outdated. Ubuntu 16.04 Sound Not Working I agree with the last post.

tried: sudo apt-get update/upgrade/upgrad-dist and a hole lot of other commands for removing, instaling and reinstaling drives (sound and video mostly) to no avail apparently… It seems to problem might be Ubuntu 15.04 No Sound If you do get a distro to make sound when the original distro didn't, get all the information you can using lspci and lsmod and various commands like amixer, aplay and Of note, my graphic card went bad early this week and I replaced it with a new Nvidia graphic card and that's when this whole mess got started. Other Issues Bad configuration files After starting PulseAudio, if the system outputs no sound, it may be necessary to delete the contents of ~/.config/pulse and/or ~/.pulse.

If all the sliders are maxed out, and the volume is still too low, you can try running the following script to reset your codec settings: $ wget $ su Ubuntu 16.04 No Sound Thanks for the info. Ive left loads of messages for help on here but so far not one reply. Thanks Reply Abhishek Prakash says September 15, 2013 at 10:21 am welcome.

Ubuntu 15.04 No Sound

I can get to my loginscreen, but when i type in my password i just get a quick flash of the terminal and the back to the login screen. Note: Setting a high value for Pre-Amp can cause sound distortion, so adjust it according to the level that suits you. Linux No Sound Output i update system with command apt-get dist-upgrade , and new version of udev might conflic. Ubuntu 14.04 No Sound In my case, I deselected 'all' then selected 'via82xx'.

The solution proposed in this page may work: start Audacity with: $ env PULSE_LATENCY_MSEC=30 audacity If the solution above does not fix this issue, one may wish to temporarily disable pulseaudio his comment is here S/PDIF) may not be enabled by default on the selected sink. That window is starting to look good Reply DJ says August 1, 2014 at 9:18 pm i have sound problem for headphones in ubuntu 12.04 and above all ubutnu until 14.04 Your playlist has great songs, but they're recorded at all sorts of different volume levels, and it's annoying. Ubuntu Sound Dummy Output

Adv Reply November 11th, 2009 #10 mammoth23 View Profile View Forum Posts Private Message First Cup of Ubuntu Join Date Nov 2009 Beans 4 DistroUbuntu 10.04 Lucid Lynx Re: Dummy Sound Card Configuration Tool

10.3.1. Volume is too low Run alsamixer and try to increase the value of the sliders, unmuting channels if necessary. this contact form and i can move mouse cursor.

Reply Abhishek Prakash says November 26, 2013 at 2:12 pm Thanks for loving It's FOSS :) Reply Hagbard Celine says November 22, 2013 at 11:48 pm Hey folks, none of the Ubuntu No Sound Output I've heard rumors of it conflicting with ALSA (works fine on my computer, but who knows). But when prayers are all you have left, that's what you do.

While there could be several reasons for no sound in Ubuntu 14.04, I will share the trick which worked for me.

Reply Abhishek Prakash says May 7, 2013 at 8:47 am Hi Matt, I had the feeling that this is not really a complete solution. Try our newsletter Sign up for our newsletter and get our top new questions delivered to your inbox (see an example). You should look for the information that was listed by the command in the previous step. Ubuntu 15.10 No Sound Create the template service file in /etc/systemd/system/resume-fix-pulseaudio@.service: [Unit] Description=Fix PulseAudio after resume from suspend [Service] User=%I Type=oneshot Environment="XDG_RUNTIME_DIR=/run/user/%U" ExecStart=/usr/bin/pasuspender /bin/true [Install] 2.

This is the maximum sampling rate of our card. S/PDIF output does not work If the optical/coaxial digital output of your motherboard/sound card is not working or stopped working, and have already enabled and unmuted it in alsamixer, try running Or press Alt+ and type gnome-volume-control You can also type this in terminal.Switch to Input tab and ensure the microphone is unmuted and the input level is not zero (preferably maximum). navigate here No HDMI 5/7.1 Selection for Device If you are unable to select 5/7.1 channel output for a working HDMI device, then turning off "stream device reading" in /etc/pulse/ might help.

What did work was going into terminal with alsamixer then I could select the correct device there using F6. Adv Reply November 11th, 2009 #9 M03BIUS View Profile View Forum Posts Private Message 5 Cups of Ubuntu Join Date Dec 2008 Location In a country Beans 29 DistroUbuntu 9.04 up vote 3 down vote I had the same problem Ubuntu 14.04. I replaced it with linux-image-extra-* which worked for me.

But, I still can't hear the system alert sound Reply Stephen WhoLikesHisSoundOn says April 11, 2016 at 10:27 am I'm running Linux Mint Rosa. Make sure to use only one method of autostarting applications. thnx again and best wishes! :) Reply Chris says December 4, 2013 at 10:15 pm worked for me, thanks! I didn't have any way to get audio over the graphics card though so I reenabled the integrated sound in my BIOS settings and that fixed my problem the first time.