Fix Linux Sound Not Working Tutorial

Home > No Sound > Linux Sound Not Working

Linux Sound Not Working

Contents

The Sound Theme tool is also accessible via System > Preferences > Sound Step 11 Try connecting headphones to different audio jacks/ports on the back-panel of the sound-card until you hopefully The steps you listed fix the issue once. Reply Doc Hego says July 16, 2013 at 12:39 pm Thanks for the post. Or if I shut down the PC and turn off the PSU and log in again. have a peek here

Reply Sandy barton says August 12, 2013 at 8:52 am Yes, it worked…I hav done killall pulseaudio …. :) Reply Abhishek Prakash says August 12, 2013 at 11:24 am So doing After installation, any sound file played (mp3) was accompanied by static, pauses, glitches, etc, to the extent of being unlistenable. If one experiences choppy sound in applications using OpenAL, change the sample rate in /etc/openal/alsoft.conf: /etc/openal/alsoft.conf frequency = 48000 Setting the PCM volume above 0 dB can cause clipping. Be sure to know what all cards in alsamixer look like, and what all the tabs in pavucontrol look like. http://www.troubleshooters.com/linux/sound/sound_troubleshooting.htm

Ubuntu 15.04 No Sound

Is your volume turned all the way down, or is your speaker muted? Make sure that the speaker cable is securely plugged into the "output" audio socket on the back of the computer. As a matter of fact, saplay and sarecord are really the same program, and either can be made into each other with the s-P switch for playing, or the s-C switch

The Fedora Project is maintained and driven by the community and sponsored by Red Hat. Alternative way to enable SPDIF output automatically on login (tested on SoundBlaster Audigy): add following lines to /etc/rc.local: # Use COAX-digital output amixer set 'IEC958 Optical' 100 unmute amixer set 'Audigy This predefined diagnostic won't solve all sound problems, but it will solve most of them, and do it quickly. Ubuntu 15.10 No Sound See the #Outputs by PulseAudio error status check utilities section.

After rebooting I got some sort of mdm error and the graphical interface would not work. Ubuntu 14.04 No Sound You can see all the available models in the kernel documentation. Greetings Roland Reply Jagadeesh says September 14, 2013 at 10:05 am Great super work around. https://help.ubuntu.com/stable/ubuntu-help/sound-nosound.html Reference request: optimizing procedures on lists in dynamic languages by performing safety checks in advance Flat renting in Berlin for medium-term period Is there a standard DNS record to indicate the

Is there anything I haven't tried yet? Ubuntu No Sound Hdmi Manual Installation If you've done the basic troubleshooting listed above and your sound still isn't working, you may have found a bug in Ubuntu. Whenever pulseaudio gives up, the following seems to get it back: pulseaudio -kill sudo alsa force-reload pulseaudio -start The indicator in the task bar doesn't come back alive, though pavucontrol works It has pretty much been replaced by ALSA, but some people have oss installed because some old software can play only through oss.

Ubuntu 14.04 No Sound

Establish a Baseline This is a must! news I was hoping the first alternative would be a more permanent solution, but after doing it, the sound won't work at all and I can't open my Unity Tweak Tool (keeps Ubuntu 15.04 No Sound Make sure to use only one method of autostarting applications. Ubuntu 16.04 No Sound Reply JHG says August 30, 2015 at 9:29 pm amixer -c 0 cset iface=MIXER,name='Headphone Playback Volume' 100% Reply fuad says August 28, 2015 at 9:58 pm mine is ubunutu 14 version

For example, being able to send audio to your A/V receiver via your graphics card's HDMI output, while also sending the same audio through the analogue output of your motherboard's built-in navigate here volume jumps to 100% after running application) If changing the volume in specific applications or simply running an application changes the master output volume this is likely due to flat volumes Adding the line ipc_key_add_uid 0 to the pcm.dmixer block disables this locking. But every few restarts, your old friend "Dummy Output" will be back to greet you. Ubuntu No Sound Output

Going backwards… Reply Bob aliceson says February 21, 2016 at 4:27 am These two commands destroyed my system (linux mint 17.2) . After creating this file, reboot. If this occurs, use the other useful GUI tool, paprefs, to check under the "Simultaneous Output" tab for a virtual simultaneous device. Check This Out Or you can click on the 'More Apps' button, click on the 'See more results' by the installed section, and find it in that list of applications.

For example here, but check that it is the correct version of that document for your kernel version. Ubuntu 16.04 Sound The file may also be generated immediately using: # alsactl store Problems with availability to only one user at a time You might find that only one user can use the See #Fallback device is not respected.

Is there a way to get sound work all the time?

sudo alsa force-reload Unloading ALSA sound driver modules: (none loaded). Create udev rule to make PulseAudio choose your PulseAudio configuration file specific to the sound card. To use aoss, when you run the program, prefix it with aoss, e.g.: aoss realplay pcm.!default{ ... } doesnt work for me anymore. Ubuntu Sound Dummy Output Instead, copy the commands from this web page and paste them into the terminal.

To do this, create a file named /etc/modprobe.d/sound.conf, with the following contents: options snd_hda_intel model=(recommended parameter) For example: options snd_hda_intel model=3stack if the recommended model was '3stack'. Reply Abhishek Prakash says September 2, 2014 at 11:54 am Welcome Maurice. Reason: The problem is using ALSA tools for controlling PulseAudio, see PulseAudio#Keyboard volume control for better way. (Discuss in Talk:PulseAudio/Troubleshooting#) In setups with multiple outputs (e.g. 'Headphone' and 'Speaker') using plain http://vicnot.net/no-sound/linux-mint-11-sound-not-working.html When you seem to have ruled out everything else, investigate sound drivers.

Use the M key to toggle between muted (MM) and unmuted (00) states. Rename (that's safer) /.config/pulse to /.config/tmp_pulse.